towerops/priv/mibs/packetlight/SL-TESTS-MIB

-- *****************************************************************
-- Tests MIB
-- *****************************************************************

SL-TESTS-MIB DEFINITIONS ::= BEGIN

IMPORTS
	MODULE-IDENTITY, OBJECT-TYPE, Counter32,
	NOTIFICATION-TYPE 			     	FROM SNMPv2-SMI
	DisplayString, TruthValue, 
	TimeStamp, DateAndTime, RowStatus	FROM SNMPv2-TC
	MODULE-COMPLIANCE, OBJECT-GROUP,
	NOTIFICATION-GROUP                  FROM SNMPv2-CONF
	InterfaceIndex		               	FROM IF-MIB
	PerfCurrentCount, PerfIntervalCount,
	PerfTotalCount                      FROM PerfHist-TC-MIB
    slMain				        		FROM SL-MAIN-MIB;

slTests MODULE-IDENTITY
	LAST-UPDATED "200101180000Z"
	ORGANIZATION "PacketLight Networks Ltd."
	CONTACT-INFO
		"Omri_Viner@PacketLight.com"
	DESCRIPTION
		"This MIB module describes the available on-demand tests."
	::= { slMain 13 }

slTestsIfLoop		OBJECT IDENTIFIER 	::= { slTests 1 }
slTestsTraps		OBJECT IDENTIFIER 	::= { slTests 2 }
slTestsTraps0		OBJECT IDENTIFIER 	::= { slTestsTraps 0 }



-- *******************************************
--
-- The If Loopback Test Table
--
-- *******************************************
	
slTestsIfLoopTable OBJECT-TYPE
	SYNTAX  SEQUENCE OF SlTestsIfLoopEntry
	MAX-ACCESS  		not-accessible
	STATUS  			current
	DESCRIPTION
		"The port loopback test table. This table controls the 
		port loopback tests."
	::= { slTestsIfLoop 1 }

slTestsIfLoopEntry OBJECT-TYPE
	SYNTAX  SlTestsIfLoopEntry
	MAX-ACCESS  not-accessible
	STATUS  current
	DESCRIPTION
		"This entry is used to operate an port loopback test."
	INDEX   { slTestsIfLoopIfIndex }
	::= { slTestsIfLoopTable 1 }

SlTestsIfLoopEntry ::=
	SEQUENCE {
		slTestsIfLoopIfIndex			InterfaceIndex,
		slTestsIfLoopDuration			INTEGER,
		slTestsIfLoopStatus				INTEGER,
		slTestsIfLoopType				INTEGER,
		slTestsIfLoopMode				INTEGER,
		slTestsIfLoopErrors				Counter32,
		slTestsIfLoopResult				INTEGER,
		slTestsIfLoopPassedSeconds		INTEGER
	}	

slTestsIfLoopIfIndex OBJECT-TYPE
    SYNTAX      InterfaceIndex
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The Interface Index of the port that should be loopped back."
    ::= { slTestsIfLoopEntry 1 }

slTestsIfLoopDuration OBJECT-TYPE
	SYNTAX        INTEGER
	MAX-ACCESS    read-write
	STATUS        current
	DESCRIPTION
		"The test duration in 1/10 Sec. The maximum allowed
		duration is 1 hour. After this time the port configuration
		returns to its original setting and the Agent automatically
		deletes the entry from the table."
	::= { slTestsIfLoopEntry 2 }

slTestsIfLoopStatus OBJECT-TYPE
	SYNTAX        INTEGER {
		start(1),
		stop(2),
		fail(3)
	}
	MAX-ACCESS    read-write
	STATUS        current
	DESCRIPTION
		"This variable is used to start or stop a loopback test.
		In order to start a test the NMS should set the value to start(1).
		If the test mode is toggle, the NMS should stop the test by setting the value
		to stop(2).
		In the case of prbs test, after the test has stopped, 
		if the test fails the value of the status shall be fail(3)."
	::= { slTestsIfLoopEntry 3 }

slTestsIfLoopType OBJECT-TYPE
	SYNTAX        INTEGER {
		terminal(1),
		facility(2),
		prbs(3),
		otnPrbs(4)
	}
	MAX-ACCESS    read-write
	STATUS        current
	DESCRIPTION
		"The loopback type:
          facility
             The received signal at this interface is looped back
             out through the corresponding transmitter in the return
             direction.
          terminal 
             The signal that is about to be transmitted is connected
             to the associated incoming receiver.
          prbs 
             send and recieve prbs pattern.
          otnPrbs
          	 send and receive OTN prbs"
	::= { slTestsIfLoopEntry 5 }

slTestsIfLoopMode OBJECT-TYPE
	SYNTAX        INTEGER {
		timeout(1),  
		toggle(2)    
	}
	MAX-ACCESS    read-write
	STATUS        current
	DESCRIPTION
		"The loopback mode:
          timeout
             In this mode the duration of the loopback is determined
             by the slTestsIfLoopDuration object.
          toggle     
             In this mode the loopback should be toggled explicitly
             by the user."
	::= { slTestsIfLoopEntry 6 }

slTestsIfLoopErrors OBJECT-TYPE
	SYNTAX        Counter32
	MAX-ACCESS    read-only
	STATUS        current
	DESCRIPTION
		"The prbs errors are counted only of the test succeeded."
	::= { slTestsIfLoopEntry 7 }

slTestsIfLoopResult OBJECT-TYPE
	SYNTAX        INTEGER {
		success(1),
		fail(2)
	}
	MAX-ACCESS    read-only
	STATUS        current
	DESCRIPTION
		"This variable is used for prbs test result indication."
	::= { slTestsIfLoopEntry 8 }

slTestsIfLoopPassedSeconds OBJECT-TYPE
	SYNTAX        INTEGER 
	MAX-ACCESS    read-only
	STATUS        current
	DESCRIPTION
		"Number of seconds passed since the test started."
	::= { slTestsIfLoopEntry 9 }


-- *******************************************
--
-- The If Tests Traps
--
-- *******************************************

slTestsTrapsLoopbackActive OBJECT-TYPE
       SYNTAX    	 TruthValue
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
          "The Loopback is active Yes/No."
        ::= { slTestsTraps 1 }

slTestsTrapsLoopbackTableChanged NOTIFICATION-TYPE
	OBJECTS { slTestsIfLoopIfIndex, slTestsIfLoopType, slTestsTrapsLoopbackActive }
	STATUS  current
	DESCRIPTION
		"A slTestsTrapsLoopbackTableChanged trap is sent when the
		content of slTestsIfLoopTable changes. When the loop back is deleted
		the returned value of slTestsIfLoopActivity should be false."
	::= { slTestsTraps 2 }

slTestsTrapsLoopbackTableChanged0 NOTIFICATION-TYPE
	OBJECTS { slTestsIfLoopIfIndex, slTestsIfLoopType, slTestsTrapsLoopbackActive }
	STATUS  current
	DESCRIPTION
		"A slTestsTrapsLoopbackTableChanged trap is sent when the
		content of slTestsIfLoopTable changes. When the loop back is deleted
		the returned value of slTestsIfLoopActivity should be false."
	::= { slTestsTraps0 2 }

END