Update UserSettingsLive to properly handle browser back/forward buttons
by syncing all modal state to URL parameters.
Changes:
- Update handle_params/3 to read modal param and set modal states
- Add build_settings_path/2 helper to construct URLs with preserved params
- Update all modal show/close handlers to use push_patch instead of assign:
- add_token modal
- token_created modal (shown after creating token)
- revoke_all modal
- add_device modal (TOTP)
- device_qr modal (shown after creating device)
- recovery_codes modal
Behavior:
- Browser back button now closes modals without navigating away
- URL reflects current modal state (?modal=add_token, etc.)
- Tab and page params preserved when opening/closing modals
- Bookmarkable URLs restore exact modal state
Follows idiomatic Phoenix LiveView pattern using push_patch/2 and
handle_params/3 as documented in CLAUDE.md.
Co-Authored-By: Claude Sonnet 4.5 <noreply@anthropic.com>
Add TIER 3 MEDIUM priority optical power sensors for comprehensive AF-LTU link diagnostics.
Per-chain monitoring enables detection of imbalanced signals and fiber issues.
AirFiber AF-LTU additions:
- RX Power Chain 0: Received optical power chain 0 in dBm
OID: .1.3.6.1.4.1.41112.1.10.1.4.1.5
- RX Power Chain 1: Received optical power chain 1 in dBm
OID: .1.3.6.1.4.1.41112.1.10.1.4.1.6
- RX Ideal Power Chain 0: Ideal received power chain 0 in dBm
OID: .1.3.6.1.4.1.41112.1.10.1.4.1.7
- RX Ideal Power Chain 1: Ideal received power chain 1 in dBm
OID: .1.3.6.1.4.1.41112.1.10.1.4.1.8
- TX EIRP: Transmit effective isotropic radiated power in dBm
OID: .1.3.6.1.4.1.41112.1.10.1.2.6
Impact:
- Per-chain monitoring detects imbalanced signal levels across RF chains
- RX Ideal Power comparison identifies suboptimal alignment or hardware issues
- TX EIRP monitoring ensures regulatory compliance and proper power output
- Enables proactive fiber and optical component troubleshooting
Implementation:
- All sensors use dbm sensor type for dBm units
- OIDs match LibreNMS LibreNMS/OS/AirosAfLtu.php exactly
- No divisors needed (values already in dBm)
Priority: TIER 3 MEDIUM (6-8 hour effort, enhanced diagnostics)
Gap Status: AF-LTU parity 80% → 90%
Remaining: UniFi channel-to-frequency conversion (requires vendor module work)
Files:
- priv/profiles/os_discovery/airos-af-ltu.yaml
- CHANGELOG.txt
Add TIER 2 HIGH priority wireless metrics for comprehensive AirFiber point-to-point monitoring.
These sensors enable capacity planning, link budget analysis, and interference detection.
AirFiber AF60 additions:
- Frequency: Operating frequency in MHz (OID: .1.3.6.1.4.1.41112.1.11.1.1.2)
- Distance: Link distance in km, divisor 1000 (OID: .1.3.6.1.4.1.41112.1.11.1.3.1.15)
- TX Capacity: Transmit capacity in Mbps, divisor 1000 (OID: .1.3.6.1.4.1.41112.1.11.1.3.1.7)
- RX Capacity: Receive capacity in Mbps, divisor 1000 (OID: .1.3.6.1.4.1.41112.1.11.1.3.1.8)
- Local RSSI: Local received signal strength in dBm (OID: .1.3.6.1.4.1.41112.1.11.1.3.1.3)
- Remote RSSI: Remote received signal strength in dBm (OID: .1.3.6.1.4.1.41112.1.11.1.3.1.18)
- Local SNR: Local signal-to-noise ratio in dB (OID: .1.3.6.1.4.1.41112.1.11.1.3.1.4)
- Remote SNR: Remote signal-to-noise ratio in dB (OID: .1.3.6.1.4.1.41112.1.11.1.3.1.19)
AirFiber AF-LTU additions:
- Frequency: Operating frequency in MHz (OID: .1.3.6.1.4.1.41112.1.10.1.2.2)
- Distance: Link distance in km, divisor 1000 (OID: .1.3.6.1.4.1.41112.1.10.1.4.1.23)
- TX Capacity: Transmit capacity in Mbps, divisor 1000 (OID: .1.3.6.1.4.1.41112.1.10.1.4.1.3)
- RX Capacity: Receive capacity in Mbps, divisor 1000 (OID: .1.3.6.1.4.1.41112.1.10.1.4.1.4)
Impact:
- Distance enables link budget analysis and alignment verification
- RSSI/SNR enable interference detection and signal quality monitoring
- Capacity metrics enable throughput monitoring and bandwidth planning
- Frequency confirms correct channel selection
Implementation:
- All sensor definitions match LibreNMS exactly
- Divisors applied for proper unit conversion (1000 for distance/capacity)
- Source: LibreNMS LibreNMS/OS/AirosAf60.php, LibreNMS/OS/AirosAfLtu.php
Priority: TIER 2 HIGH (4-6 hour effort, capacity planning and troubleshooting)
Gap Status: AF60 parity 50% → 80%, AF-LTU parity 60% → 80%
Next: TIER 3 - UniFi channel-to-frequency conversion, AF-LTU optical power sensors
Files:
- priv/profiles/os_discovery/airos-af60.yaml
- priv/profiles/os_discovery/airos-af-ltu.yaml
- CHANGELOG.txt
MikroTik mtxrGaugeTable temperature sensors report values in whole
degrees Celsius, not tenths. The MIB defines the unit as 'celsius(1)'
without the 'deci-' prefix used for voltage (dV), current (dA), and
power (dW).
This matches LibreNMS behavior which does not apply a divisor to
temperature sensors.
Co-Authored-By: Claude Sonnet 4.5 <noreply@anthropic.com>
